Ideal for your DIY jobs.

Properties
Strips paints, stains, varnishes… without sanding.
It also removes deep stains.
Makes the coating water soluble – remove with a simple rinse.
It does not evaporate, it does not dry out in hot weather.
It is reactivated by moistening.
No sanding.
Effective, up to 8 coats of paint in one application:
Destination
Effective on wood**, PVC, metal***…
Effective, up to 8 layers of paint stripped in a single application.
** Except oak, chestnut, red cedar and marquetry.
***Except aluminum.
Tips for correct application
Always do a preliminary test.
Use protective gloves, a nylon brush or a fiber brush.
The action time varies from a few minutes to several hours depending on the type of coating (glycerophthalic or acrylic) and the number of layers. Check its action using a spatula.
Regarding stripping on absorbent supports, neutralization with NET-TROL is always recommended.
Application
Apply a thick layer of DILUNETT over the entire surface to be stripped. Let the product work. In case of drying, reactivate with a fine spray of water. Rinse with clean water and a brush or HP cleaner (max. 60 bars). NOTE: Using hot water makes removal easier. After stripping wood, always apply NET-TROL (on damp wood) and IMMEDIATELY after rinsing off DILUNETT. Consult the application method on the packaging.

Properties
Anticorrosive aluminum finish with a very shiny appearance.
High reflective film – light and heat
Excellent penetration and adhesion properties of OWATROL OIL – Will not peel or flake.
Restores rusty surfaces.
Ideal for aggressive weather conditions. Resists chemical attacks.
Easy application.
Protects against corrosion.
Very good quality film formation (adhesion, flexibility, even films).
High temperature resistance up to 175°C.

Application
Apply a coat of OWATROL RA85. If two coats are required, allow 24 hours to pass between coats.
OWATROL RA85 is based on OWATROL OIL, which allows a uniform and glossy film to form while maintaining high flexibility.

OWATROL® OIL. This antioxidant treatment allows your materials to be more resistant, stops oxidation and protects them from external aggressions. To be used as a base coat before finishing paint, it guarantees a quality result and protects your materials from heat and humidity thanks to its protective film.

Properties
Penetrating antioxidant and direct insulator on rust
– Penetrates healthy metal while expelling air and moisture.
– Forms an insulating and flexible protective film. Resistant to + 175º C.

Additive for paints, varnishes and fatty binder primers…
– Dilute: 25% per litre in the first layer or 50% if the surface is smooth or porous.
– Converts paints and varnishes into antioxidants. Facilitates application.
– Replaces solvents, does not evaporate.
– Increases the covering power of finishes.
– Adhesion to all smooth substrates: glass, pvc, ferrous or non-ferrous metals…
– Allows you to prepare aluminium, galvanized and zinc without sanding.

Decorative appearance
– Preserves the rusty appearance of the supports while protecting them.

Properties

OWATROL® C.I.P.  can be applied directly onto stable oxidation.  Impregnates and stabilizes in difficult conditions.
Anti-corrosion primer, red/brown, one-component for oxidised surfaces.
Can be applied directly onto a healthy oxidation without sanding first.
Multifunction:
1. Impregnates and deeply penetrates healthy metal.  Fills micro-cavities.
2. Radically detains the rust and stabilizes the surface in preparation for it´s finishing coat.
3. Reinforced protection: active pigments and a solid, flexible film to avoid any risk of cracking.
4. Adheres to all metal surfaces.  Compatible with the majority of finishes, preferably one-component finishes.
Temperature Resitant to + 175º C.

Properties

• Lasting Gloss finish.  Brings out the beauty in the wood.
• Resistant and flexible film.
• Very fluid varnish.  Doesn´t hide the wood grain.
• Easy application without the need to sand between coats (except before the last coat).
• Apply on top of Deks Olje D1.
• Use only above the waterline.

Application

Apply 3 to 6 coats of Deks Olje D.2 depending on the exposure of the surface.  Allow to dry at least 12 hours between coats.  It is  not necessary to sand between coats.  Allow to dry 3 to 4 days before putting to use.

Description

Weather proofing treatment.  Transparent mat saturator for exotic hard woods (including teak).  Deeply nourishes wood guaranteeing a long-lasting high protection for decks and garden furniture.  Ideal for maintenance of terraces, garden furniture and boats.

Properties

Applicable on horizontal or vertical surfaces.
Deeply saturates and protects hard and/or oily woods.
Excellent penetration without forming a film.
Replaces teak oils without darkening.
Transparent, doesn´t hide the grain of the wood.
Protection against mildew.
Simple to maintain with water and soap.
Speedy renovation with no need to sand or strip.
Can be used alone (mat) or with a top coat of Deks Olje D.2 (High Gloss).

Can be used above or below the waterline.  Creates an excellent insulation or base before conventional treatment.

Application

Apply one saturated coat of DEKS OLJE D.1 and allow to penetrate the wood between 15-30 minutes. Repeat until it is saturated.  Do not allow to dry between coats.  Once saturated, always brush or clean the excess product to avoid any trace of gloss during the drying period.